Front OptionsThe 385C Material Handler is available with a choice of two different front lengths. The (17.2 m) 56'6" front with straight boom can be used for barge unloading or scrap handling. The (22 m) 71.5' can be used in scrap handling. Both front options are designed and built by Caterpillar.
Stress Relieving Booms and SticksBuilt to maximize strength and minimize structure weight.
Efficient Design of Welded Box-section StructuresThe design with thick, multi-plate fabrications in high stress areas allows structures to flex, dissipating stresses and maximizing strength.
385C MH Two-piece Fronts by Caterpillar The two-piece fronts meet your material handling needs with excellent lift performance and working range whether operating in close or at full reach. Built for strong performance and long service life. » Learn More
PerformanceThe C18 with ACERT™ Technology offers 20% greater displacement than the 3406C, and runs at 10% lower speeds for better fuel economy and reduced wear. The 385C MH, equipped with a C18 engine, provides 16% more horsepower compared to the 3406C in the 375 MH.
Fuel ConsumptionWith ACERT Technology, the C18 engine meets U.S. EPA Tier 3 emissions regulations while delivering good fuel economy.
EmissionsACERT Technology is a differentiated technology that reduces emissions at the point of combustion. The technology capitalizes on Caterpillar’s proven leadership in three core engine systems: fuel, air and electronics.
Low Sound and Vibration LevelsThe engine mounts are rubber-isolating mounts matched with the engine package to provide optimum sound and vibration reduction. Another benefit of ACERT™ Technology, the C18 engine can shape the rate of fuel injection, a process that reduces engine noise levels and vibration.
Fuel SystemsThe CAT® C18 engine features electronic controls that govern the mechanically actuated unit fuel injection (MEUI) system. MEUI provides the high-pressure required to help reduce particulate emissions and deliver better fuel economy through finer fuel atomization and more complete combustion.
Cooling SystemsStandard screens at the radiator inlet along with an optional automatic reversing fan and door mounted filters keep the radiator and oil cooler clean in dirty scrap yard environments to ensure optimum cooling performance.
Air CleanerThe radial seal air filter features a double-layered filter core for more efficient filtration and is located in a compartment behind the cab. A warning is displayed on the monitor when dust accumulates above a preset level.
TurbochargerThe CAT® C18 engine uses a Wastegate Turbocharger for improved performance. This turbocharger controls the air volume to the cylinders and works efficiently during low and high load conditions.
Cold Weather StartStarting package consists of four batteries, heavy-duty harness, large capacity starting motor and the ether starting aid. With this standard feature, the 385C MH has the capability to start at -32° C (-25.6° F).
C18 Engine with ACERT™ Technology Built for power, reliability, economy and low emissions. » Learn More
Advanced Carbody DesignAdvanced carbody design stands up to the toughest applications. - Modified X-shaped box-section carbody provides excellent resistance to torsional bending.
- When track roller frames are in working position, the lift capacity over-the-side and over-the-front are the same.
- Robotic welding helps ensure consistent, high-quality welds throughout the manufacturing process.
Thicker Carbody PlatesThicker carbody plates, increased box-section height, and a wider carbody than found on standard excavators provide increased weight and load capacities.
Robot-welded Track Roller FramesPress-formed, pentagonal units deliver exceptional strength and service life.
Upper FrameIs specifically designed for the scrap and material handling market. It is built of higher strength material and thicker steel sections to handle the increased swing loads developed with the longer fronts and heavier counterweights used in material handling. - Boom tower doubler plates add reinforcement for increased side loads and payloads.
- Box-section reinforcement of the cab outrigger frames support cab risers.
- Box-section cylinder mounts help handle increased torsional loads and payloads.
- Horizontal mounting plates provide more surface area for swing drive and swing bearing mounting bolts to handle increased loads and movement.
- Outer frame utilizes curved side rails, which are die-formed, for excellent uniformity and strength throughout the length.
- Inverted U-channels span the width of the main frame and are formed, rather than fabricated, for superior strength and reduced weight.
- Boom foot and engine mount areas are reinforced for additional strength.
- Sheet metal supporting structure is improved by integrating the mounting into upper frame structure.
IdlersTrack Idlers are positioned lower than standard excavator idlers to help better resist tipping over the front.
Structures The 385C MH structural components are the backbone of the machine's durability. » Learn More
Material Handler HydraulicsSpecifically designed to meet your hydraulic attachment requirements, the grapple open/close circuit works with the other implement circuits to deliver smooth, simultaneous, multi-function control. The rotate circuit, using main pump flow, provides a separate fully adjustable control valve that allows this configuration to meet various grapple manufacturer’s flow requirements. A separate fixed displacement piston pump is used to provide the hydraulic power to run an optional 40 kW generator system.
Caterpillar 40 kW Solid State Generator SetPowers magnets up to 87" (2110 mm) in diameter. A Caterpillar state-of-the-art electronic magnet controller and generator are linked to provide trouble free service. The new controller completely eliminates traditional contactor maintenance and it is supported and warranted through your CAT® dealer.
GensetGenset is mounted in the riser for improved protection.
Walker Scrapmaster Series Scrap Handling MagnetsThe magnets feature cast steel case and alloy steel suspension chain.
Cat Material Handler Hydraulic Systems The 385C MH hydraulic system is designed to handle the specific requirements of the Material Handling Industry. » Learn More
Smart BoomAllows the boom to float upwards as the clamshell bucket or grapple closes. This reduces stress on the machine.
Soft SwingSoftens the deceleration portion of the swing cycle.
Automatic Reversing FanReverses the engine and coolant fan to remove debris from radiator coils.
A New Cab Mounted Magnet System Monitor/ControlProvides system information to the operator through a series of indicators, lights and a rotary selector switch. The indicator lights provide the following information. Magnet “On”: Magnet is turned on. Generator “Hot”: Generator is overheated and must be cooled down. The generator should be run under “no load” until the indicator turns off. Voltage Fault: Voltage too high or too low. May indicate service is required. Ground Fault: The magnet, generator or cable is grounded. Service is required. Over 75% Duty Cycle: The “magnet on” time exceeds 7.5 minutes in a ten minute time frame indicating the operator technique needs to be adjusted.
Rotary Selector SwitchAllows the operator to optimize the magnet performance for different grades of scrap from within the cab.
Sealed Greased TrackThe 385C MH comes standard with the new grease lubricated track called GLT4. The track links are assembled and sealed with grease to decrease internal bushing wear, reduce travel noise and extend service life lowering operating costs.
Wide 4826 mm (15'10") Track GaugeProvides over-the-side stability equal to over-the-front stability to handle heavy loads and improve productivity. Carbody plates are 5 mm thicker than standard, high strength swing bearing bolts plus larger box-section height team up to provide superior joint retention and durability in material handling applications.
Caterpillar Designed and Built, 1.9 m (6' 5") Up and 1.2 m (4' ) Out Cab RiserThe cab riser gets your operator to an operating height with excellent visibility for loading or unloading your processing equipment, trucks and rail cars. Access to the cab is provided by a platform which extends around the riser to allow windshield cleaning. The cab riser can also be manually tilted forward for shipping.
High Pressure ScreensHigh pressure screens mounted at the boom base protect the machine from contamination should the tool fail.
Additional Features The 385C MH has been designed with many benefit adding features to enhance the machine's performance in material handling applications. » Learn More
Service IntervalsService intervals are extended to reduce maintenance costs.
• Engine oil, oil filter and fuel filters at 500 hours
Oil and Pressure PortsOil sample and pressure ports provide easy checking of machine condition and are standard on every machine.
Hydraulic Capsule FiltersThe return filters or capsule filters for the hydraulic system are located beside the hydraulic tank. The filter elements are removable without spilling hydraulic oil.
Service PointsService points are centrally located with easy access to facilitate routine maintenance.
Point Hydraulic Sytem FilterPilot hydraulic system filter keeps contaminants from the pilot system and is located in the pump compartment.
Greasing PointsA concentrated remote greasing block on the boom delivers grease to hard-to-reach locations.
Radial Seal CleanerRadial seal main air cleaner with precleaner has a double-layered filter element for more efficient filtration. No tools are required to change the element.
Fuel-Water SeperatorThe water separator removes water from fuel, even when under pressure, and water level can be monitored in the cab.
Service and Maintenance Fast, easy service has been designed in with extended service intervals, advanced filtration, convenient filter access and user-friendly electronic diagnostics for increased productivity and reduced maintenance costs. » Learn More
Product SupportYou will find nearly all parts at our dealer parts counter. CAT® dealers utilize a worldwide computer network to find in-stock parts to minimize machine downtime. You can save money with CAT® remanufactured components.
Machine SelectionMake detailed comparisons of the machines you are considering before you buy. What are the job requirements, machine attachments and operating hours? What production is needed? Your CAT® dealer can provide recommendations.
PurchaseLook past initial price. Consider the financing options available as well as day-to-day operating costs. This is also the time to look at dealer services that can be included in the cost of the machine to yield lower equipment owning and operating costs over the long run.
Customer Support AgreementsCAT® Dealers offer a variety of product support agreements, and work with customers to develop a plan the best meets specific needs. These plans can cover the entire machine, including attachments, to help protect the customer’s investment.
Maintenance ServicesRepair option programs guarantee the cost of repairs up front. Diagnostic programs such as Scheduled Oil Sampling, Coolant Sampling and Technical Analysis help you avoid unscheduled repairs.
ReplacementRepair, rebuild or replace? Your CAT® Dealer can help you evaluate the cost involved so you can make the right choice.
Complete Customer Support CAT® Dealer services help you operate longer with lower costs. » Learn More
|
United States / Canada [change]
Visit Caterpillar.com
.png){kind=icon}
Social Media