C32 ACERT Tier 3

Back

Extended Warranty and Support
Learn More

Overview

Generator Set Specifications

Units:
Minimum Rating 730 ekW (913 kVA) 730 ekW (913 kVA) Less
Maximum Rating 940 ekW (1175 kVA) 940 ekW (1175 kVA) Less
Frequency 60hz 60hz Less
Speed 1800 rpm 1800 rpm Less

Engine Specifications

Engine Model Vee-12, 4-stroke-Cycle-Diesel Vee-12, 4-stroke-Cycle-Diesel Less
Bore 5.7 in 145.0 mm Less
Displacement 1959.0 in3 32.1 L Less
Stroke 6.38 in 162.0 mm Less
Aspiration Turbocharged and aftercooled Turbocharged and aftercooled Less
Governor Type Electronic Electronic Less
Fuel System MEUI MEUI Less

Generator Set Configurations

Emissions/Fuel Strategy EPA Tier III, IMO II, EU IW EPA Tier III, IMO II, EU IW Less

Generator Set Dimensions

Weight (Estimated) 15721.0 lb 7131.0 kg Less
Width 60.2 in 1528.0 mm Less
Height 65.6 in 1667.0 mm Less
Length 162.8 in/4271 mm (minimum), 175.3 in/4452 mm (maximum) 162.8 in/4271 mm (minimum), 175.3 in/4452 mm (maximum) Less

Generator Specifications

Excitation Permanent magnet Permanent magnet Less
Number of poles 4 4 Less
Number of bearings 2 roller bearings 2 roller bearings Less
Number of leads 6 6 Less
Insulation Class H Class H Less
IP Rating 23 23 Less
Voltage regulator CDVR CDVR Less

C32 ACERT Tier 3 Standard Equipment

AIR INLET SYSTEM
  • Separate circuit after-cooled (SCAC)
  • Turbocharger, jacket water cooled
  • Turbocharger inlet, 152 mm (6 in) OD straight connection

CONTROL SYSTEM
  • If an EMCP panel or MGCP option is not chosen as optional equipment,then start/stop controls must be provided by the customer
  • Electronic diagnostics and fault logging
  • Engine Protection Mode for extended ambient conditions
  • Electronic fuel/air ratio control
  • Throttle Input signal options
  • 0 - 5 Volts
  • 4 - 20 mA
  • PWM (Pulse Width Modulated)

COOLING SYSTEM
  • Separate Circuit After-Cooling (SCAC) for Heat Exchanged (HEX)& Keel cooled engines
  • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tubefor HEX cooled engines
  • SCAC pump, gear driven
  • Jacket water pump, gear driven
  • Sea water pump, bronze impeller, gear driven, for HEX cooledengines only
  • Jacket water HEX with Sea water pump Connections: 76.2 mm (3in)ID Standard
  • 4 Bolt ANSI Flange Connection
  • Jacket water HEX without Sea water pump Connection: 2.5" hosebarb connection (inlet), 76.2 mm (3in) ID Standard 4 BoltANSI Flange (outlet)
  • Keel Connections: 76.2 mm (3in) ID Standard 4 BoltANSI Flange Connection
  • SCAC and JW shunt tanks for maintaining properPump inlet pressures

EXHAUST SYSTEM
  • Water-cooled exhaust manifold & turbocharger
  • 4 Bolt 130 mm (5.12 in) diameter flanged outlet

FLYWHEELS & FLYWHEEL HOUSINGS
  • Flywheel Housing, SAE No. 0
  • Flywheel, 18 inch, 136 teeth
  • SAE standard rotation

FUEL SYSTEM
  • Duplex Fuel Filters, Spin-on, RH service
  • Fuel connections size:
  • Plate-type fuel cooler installed behind Aftercooler Shunt Tank
  • Fuel transfer pump, gear driven
  • Manual fuel priming pump

GENERATORS AND GENERATOR ATTACHMENTS
  • SR5 form wound
  • 2 roller bearings
  • Permanent magnet excitation
  • 4 pole, 6 leads, Series Star connected
  • Caterpillar's Digital Voltage Regulator (CDVR)
  • Marine Class H insulation, Class F temperature rise
  • Surface mounted platinum (PT100) 3-wire RTDs, 2 per phase
  • on stator and one each on support bearings
  • Anti-condensation space heaters (2 elements - 240 VAC, 1000 Watts
  • IP23 Protection suitable for use with Fixed Water BasedLocal Application Fire Fighting Systems (FWBLAFFS)
  • System IV insulation for harsh environment protection

LUBE SYSTEM
  • Simplex oil filters, RH service
  • Deep sump oil pan
  • RH service oil filler locations
  • RH service dipstick
  • Oil pump, gear driven

MOUNTING SYSTEM
  • Formed C-channel rails, 300mm (11.81in) height
  • Six shipped loose combined helical spring/rubber
  • isolators for installation below package base

POWER TAKE-OFFS
  • Poly-V groove for alternator drive
  • NOTE: There are no standard power take-offs available

GENERAL
  • Front damper guard
  • Common electrical bonding point on HEX and KEEL cooled engines
  • Engine does not ship with zinc components
  • Engine is certified to D2/E2 emissions cycles

C32 ACERT Tier 3 Optional Equipment

CATERPILLAR A&P PACKAGE OPTIONS

EXHAUST SYSTEM
  • Dry Elbows
  • Flexible Fitting
  • Flange
  • Muffler
  • Muffler Spark Arresting
  • Rain Cap

AIR INLET SYSTEM
  • Air Inlet Cleaner
  • Closed Crankcase Ventilation

CHARGING SYSTEM
  • Battery Chargers
  • Charging Alternators

CONTROL SYSTEM
  • Load Sharing Attachment

FUEL SYSTEM
  • Water Separator

LUBE SYSTEM
  • Duplex Oil Filters
  • Sump Pump

PROTECTION SYSTEM
  • FUEL AND OIL SHIELDING

STARTING SYSTEM
  • Electric Starting Motors - Single 24 Volt
  • Air Starting Motor
  • Dual Starting Motors (Electric and Air)
  • Air Start Accessories
  • Starting Aids - JW Heaters
  • Battery Sets - 24 Volt - Dry

LITERATURE

DECALS

PACKING
  • Export Packing

Cat® Dealer Service

Buy any piece of Cat® equipment and also get the full support and commitment of your local Cat Dealer.

Contact your local dealer
Extended Warranty and Support

Caterpillar offers a variety of integrated solutions to help you protect your investment, minimize owning and operating costs, and maximize up-time.

Learn More