< Back

Financing & Insurance
See our Current Offers
View Product Downloads
Please answer to continue. Select an option to continue. Enter a valid email address.
Yes, I would like to receive future communications (such as email) from Caterpillar extended enterprise and dealer network.


The acceptance of the M 32 C long-stroke engine series in the marine industry is a success story, whose equal is hard to find in this power class. Since its introduction in 1994, more than 1600 engines have been sold. 80% of them are marine propulsion engines, and 20% are electrical generator sets. The M 32 C series is a genuine heavy fuel engine, and 75% of all engines commissioned burn the economical heavy fuel oil. The M 32 C long-stroke series with a bore of 320 mm has continued the market success of its predecessor in this bore size. Decisive factors in its development have been maximum customer benefit requirements, i.e. economy and operational reliability. Environmental aspects, however, have also been important. Operational results have fully confirmed the design objectives.

Power Rating

Power Range 2880-4500 kW 2880-4500 kW Less

Engine Specifications

Speed Range 600 rpm 600 rpm Less
Emissions IMO II IMO II Less
Aspiration Turbocharged Turbocharged Less
Bore 12.6 in 320.0 mm Less
Stroke 18.9 in 480.0 mm Less
Rotation (from flywheel end) Counterclockwise/Clockwise Counterclockwise/Clockwise Less
Configuration 6, 8, 9 Cylinder 6, 8, 9 Cylinder Less
Swept volume 2361.619 in3 38.7 l/cyl. Less

Dimensions & Weights

Minimum Dry Weight 87082.0 lb 39.5 t Less
Minimum Length 233.7 in 5936.0 mm Less
Maximum Length 308.0 in 7823.0 mm Less
Minimum Height 151.0 in 3836.0 mm Less
Maximum Height 171.7 in 4361.0 mm Less
Minimum Width 93.2 in 2368.0 mm Less
Maximum Width 85.9 in 2182.0 mm Less

Nodular cast iron engine block and crankcase with integrated ducts for lubricating oil and charge air

Nodular cast iron engine block and crankcase with integrated ducts for lubricating oil and charge air, No piping, No cooling water in the engine block, Easy maintenance, High level of operational safety

Simplified parts spectrum by using single-pipe exhaust gas ducting

Identical cylinder parts, Reduced component complexity, Simple assembly/dismantling, Low weight, low installation volume and low vibration level

Cooling water system with simple plug-in connections

Plug-in connections for the cooling water pipes with standard closure fittings, Easy to fit, very maintenance-friendly, Identical parts for each cylinder version, Reduced number of components/parts, Increased operational safety

Pulse charging system, available as an option, for all in-line engine variants

Advantages in marine propulsion systems subject to frequent changes of load, Optimum engine acceleration without special control system arrangements

High-efficiency turbocharger

Moderate temperature level of components surrounding the combustion chamber, Corrosion-free turbocharger casing without water cooling

Cylinder liner, only cooled outside the engine block

Low wear rate due to calibration ring, Low and constant lubricating oil consumption, Long life

Engine control terminal with analog instrumentation in robust cast casing

Securely mounted with vibration damping on the crankcase, Direct and reliable display of all operating media pressures by robust pressure gauges, Engine and turbocharger speed display by vibration-protected analog instruments

Segmental camshaft design

Individual segments per cylinder, Simple to assemble and dismantle

Installation-friendly, because of pumps and filters installed on the engine

Lubricating oil automatic filter fitted to the engine, Replaces duplex filter and separate automatic filters, Pumps and filters operate without any external power, Reduces the parts requirements

Connecting rod, split off design

High level of operational safety, the result of accurately preloaded bolts

Compact module for lower valve drives and injection pump drives with cam followers

Exact straight-line guidance for low-friction and low-wear operation

Compact cylinder head design

Long intervals between overhauls, Simple and fast assembly/ dismantling because of: - plug-in connections - integrated bores - self-centering

M 32 C Standard Equipment

Air Inlet System
  • Air intake silencer / filter

Control System
  • Load sharing unit (for multiple engine plant only)
  • Protection panel (emergency stop, override, reset push buttons)
  • Protection system
  • Serial link interface (MODbus / canbus)
  • Speed governor
  • Start / stop panel

Cooling System
  • Electronic cooling water preheater
  • HT cooling water pump (engine driven)
  • 2-stage charge air cooler

Exhaust System
  • Exhaust gas expansion joint
  • Exhaust gas insulated manifolds
  • Turbocharger at flywheel end

Fuel System
  • Fuel circulating pump (attached / for MGO/MDO only)
  • Fuel indicator filter
  • Fuel pressure valve (attached / for MGO/MDO only)

  • Control push buttons and lamps
  • Emergency stop lever
  • Local control panel
  • Pressure and temperature indicator

Lube System
  • Dry sump
  • Lube oil plate cooler (separate)
  • Lube oil pump (engine driven)
  • Lube oil self-cleaning filter
  • Pressure regulating valve

Mounting System
  • High flexible coupling
  • Rigid mounting

Starting System
  • Electrical barring device
  • Starting air valve

  • Lifting device (rental)
  • Torsional Vibration Calculation (TVC)

M 32 C Optional Equipment

Air Inlet System
  • Air inlet shut-off valve
  • Air intake transition piece
  • Expansion joint
  • Silencer / filter

Control System
  • Electronic speed governor cabinet
  • Engine alarm system
  • Remote control system
  • Remote indicators (start air pressure, engine speed, etc.)
  • Starter for electric driven pumps
  • 24 DC UPS

Cooling System
  • FW/SW plate cooler
  • HT cooling water pump (electric driven)
  • LT cooling water pump (electric driven)
  • Sea water cooling pump (electric driven)
  • Steam / thermal oil cooling water preheater
  • Temperature control valve

Exhaust System
  • Silencer (with or without spark arrester)
  • Turbocharger at counter-flywheel side

Fuel System
  • Fuel oil cooler
  • HFO final preheater
  • HFO pressure regulating valve
  • HFO self-cleaning automatic filter
  • HFO supply and booster pumps (electrical driven)
  • HFO treatment and supply modules
  • HFO viscosity control device
  • Mixing tank

Lube System
  • Lube oil centrifuge
  • Lube oil pump (electrical driven)
  • Lube oil treatment and combined modules
  • Pre-lubricating oil pump (electrical driven)
  • Temperature control valve
  • Wet sump with dip stick

Mounting System
  • Flexible pipe connections
  • Resilient mounting

Starting System
  • Starting air compressor
  • Starting air receiver

  • Cat Propulsion Systems
  • Engine PTO coupling
  • PTO alternator
  • PTO shaft on counter-flywheel side
  • Reduction gear
  • Reduction gear PTO coupling

Cat® Dealer Service

Buy any piece of Cat® equipment and also get the full support and commitment of your local Cat Dealer.

Contact your local dealer
Financing & Insurance

You can count on Cat Financial to provide the best financial solutions, built just for you.

See our Current Offers