3516B (60 Hz)

3516B (60 Hz) Standard Equipment

Air Inlet System

• Air cleaner; single element canister type

Air Inlet

• Air Cleaner

Cooling

• Package mounted radiator

Exhaust

• Exhaust flange outlet

Fuel

• Secondary fuel filter
• Fuel priming pump
• Primary fuel filter with integral water separator

Generator

• IP23 Protection
• Matched to the performance and output characteristics of Cat engines

Power Termination

• Bus Bar

Control Panel

• EMCP 4 Genset Controller

General

• Paint - Caterpillar Yellow except rails and radiators gloss black

Control Panels

• Controls:
• EMCP 4.2B
• Generator mounted - Rear facing
• Text alarm / event descriptions
• Speed adjust
• Auto / start / stop control
• Engine cool-down timer
• Environmental sealed front face
• Limiter and exciter diode monitor
• 24 Volt DC operation
• Generator set packages include Caterpillar' s Voltage Regulator
• Emergency stop pushbutton
• Engine cycle crank
• Engine cool-down timer
• Alarm acknowledge
• Lamp test
• Load histogram feature
• PLC functionality
• Customizable screens
• 0 True RMS AC metering, 3-phase, +/-2% accuracy
• RPM
• Operating hours
• Digital indication for:
• DC volts
• Oil pressure (psi, kPa or bar)
• Amps (per phase & average)
• Coolant temperature
• Volts (L-L & L-N)
• Frequency (Hz)
• Power factor (per phase & average)
• kW (per phase, average & percent)
• kVAr (per phase, average & percent)
• High coolant temperature
• kVAr (per phase, average & percent)
• kVA (per phase, average & percent)
• Warning / shutdown with common LED indication of shutdowns for01/10/2018:
• Low oil pressure
• Failure to start (overcrank)
• Emergency stop
• Overspeed
• Generator phase sequence
• Programmable protective relaying functions:
• Low coolant temperature
• Low coolant level
• Battery disconnect switch
• Medium Voltage: Form wound - Permanent magnet - Winding temperature detectors - NEMA Class H insulation, Class H temperature rise at 40C ambient (125C prime / 150C standby) - Busbar connections, right side extension box, bottom cable entry - NEMA standard hole pattern
• Form wound - Permanent magnet
• Reverse power (kW) (32)
• Fuel priming pump
• NEMA standard hole pattern
• NEMA standard hole pattern
• NEMA Class H insulation, Class H temperature rise at 40C ambient (125C prime / 150C standby)
• NEMA standard hole pattern
• Serial annunciator module data link
• Flanged faced outlet(s)
• NEMA Class H insulation, Class H temperature rise at 40C ambient (125C prime / 150C standby)
• Winding temperature detectors
• Oil filter, filler and dipstick
• 45 Amp charging alternator
• NEMA Class H insulation, Class H temperature rise at 40C ambient (125C prime / 150C standby)
• ATAAC - 3516E Package Radiators shipped installed
• 1 Programmable relay outputs (Form C)
• Form wound
• Lubricating oil
• Anti Condensation Space Heater
• Permanent magnet
• English
• Oil drain lines and valve
• IVR includes reactive droop capability, 3-phase voltage sensing, KVAR/PF modes, RFI suppression, min / max exciter
• Medium Voltage:
• Over / under frequency (81 o/u)
• Customer data link (Modbus RTU)
• NEMA Class H insulation, Class H temperature rise at 40C ambient (125C prime / 150C standby)
• Fumes disposal
• Secondary fuel filters
• Flywheel and flywheel housing - SAE No. 00
• Rubber anti-vibration mounts (shipped loose)
• Flexible fuel lines - shipped loose
• ADEM A3
• Communications:
• Anti-vibration mounts (shipped loose)
• Winding temperature detectors
• Permanent magnet
• 4 Programmable relay outputs (Form A)
• Busbar connections, top center mounted, top cable entry
• Permanent magnet
• Gear type lube oil pump
• Winding temperature detectors
• Medium Voltage:
• SAE Standard rotation
• Overcurrent (50/51)
• Random wound
• Winding temperature detectors
• Over / under voltage (27/59)
• Integral lube oil cool
• Right hand servicing
• 6 lead
• Internal excitation
• Caterpillar yellow with high gloss black rails and radiator
• Form wound
• Cat Connect
• Fuel cooler; not included with packages without radiator
• Busbar connections, right side extension box, bottom cable entry
• 1 Programmable digital outputs
• 3 Analog inputs
• Winding temperature detectors
• Accessory module data link
• Number of I/O varies on options selected:
• Battery and battery rack w/cables
• 24 Volt electric starting motor
• Permanent magnet
• Dry exhaust manifold
• Class H insulation, Class F temperature rise at 40C ambient (105C prime / 130C standby)
• Certified standard PGS provided
• High Voltage:
• Rails - engine / generator / radiator mounting
• Busbar connections, right side extension box, bottom cable entry
• 6 Customer programmable digital inputs
• Reverse reactive power (kVAr) (32RV)
• NEMA standard hole pattern
• 3 Phase brushless, salient pole
• Low Voltage:
• Form wound
• Busbar connections, right side extension box, bottom cable entry
• Controls: Speed adjust - Auto / start / stop control - Engine cool-down timer - Engine cycle crank - Alarm acknowledge - Lamp test - Load histogram feature - PLC functionality - Customizable screens -0 True RMS AC metering, 3-phase, +/-2% accuracy

3516B (60 Hz) Optional Equipment

Control System

• EMCP 4.3, EMCP 4.4

Air Inlet System

• Dual element air cleaner
• Single element filter

Exhaust

• Exhaust mufflers

Cooling System

• Standard ambient radiators
• Optional installed radiator
• Water level switch gauges
• Coolant
• Air inlet protection including air shut off magnetic switch
• Optional installed ATAAC radiators
• Standard ambient ATAAC radiators

Generator

• Internal excitation (IE)
• Oversize and premium generators
• Anti-condensation heater
• Permanent magnet excitation (PMG)

Power Termination

• Circuit breakers, UL listed
• Circuit breakers, IEC compliant

Control Panels

• Load share module
• Remote monitoring software
• EMCP 4.3
• Generator temperature monitoring & protection
• EMCP 4.4
• Digital I/O module
• EMCP 4.2

Exhaust System

• Exhaust Offset
• Clean emission parets
• Y adapters
• Flange and exhaust expanders
• Flexible fittings
• Elbows
• Mufflers
• Flanges

Fuel System

• Primary fuel filter

General

• US aid emblem
• Special paint
• CSA Certification
• EU Certificate of Conformance (CE)
• Integral & sub-base fuel tanks
• Integral & sub-base UL listed dual wall fuel tanks
• EEC Declaration of Conformity
• Automatic transfer switches (ATS)
• The following options are based on regional and product configuration:
• Enclosures: sound attenuated, weather protective
• Seismic Certification per applicable building codes: IBC 2000, IBC 2003, IBC 2006, IBC 2009, CBC 2007
• UL 2200 package

Mounting

• IBC isolators
• Rubber anti-vibration mounts
• Spring-type vibration isolator

Generators and Attachments

• Generator conversions IE to PM
• 380, 416, 440, 480, 600, 2400, 4160 Volts, 3 phase, 1800 rpm, RW, PM, No. of leads: 6, Picth: 0.6667 - 1600 and 1800 Frames
• Space heater
• 380, 440, 480, 600 Volts, 3 phase, 1800 rpm, RW, IE, No. of leads: 6, Picth: 0.6667 - 1600 Frame
• 380, 440, 480, 600 Volts, 3 phase, 1800 rpm, RW, PM, No. of leads: 6, Picth: 0.6667 - 1600 Frame
• Alternator air cleaner

Intrumentation

• Pyrometer and thermocouples

Lube System

• Prelube pump groups
• Oil lever regulator
• Lube oil

Starting/Charging

• Air starting motor with control and silencer
• Heavy-duty starting system
• Charging alternator
• Battery chargers
• Oversize batteries
• Jacket water heater

Crankcase Systems

• Crankcase ventilation system
• Crankcase protection group: No explosion relief valves; Explosion relief valves

Mounting System

• IBC vibration isolators
• Spring type vibration isolators
• Puck style low efficiency isolators

Power Connections

• Right, left side and rear power connections
• Neutral ground connections
• Center post busbars
• Grounding groups

Special Tests / Reports

• Standard engine test charge
• Generator set test report
• CSA certification
• Special package tests: PGS test report @ 1.0 and 0.8 power factors
• Torsional vibration analysis TVA report
• IBC certification
• Fuel consumption test

Starting / Charging Sytem

• Jacket water heaters